microfluidic dish PimCell® Voice

Details

Ref. number:                 131-1212-22

Price:                              € 480,00 per one Dish

Size:                                35x10 mm

Aperture:                        22 mm

Material:                        Black polystyrene surrounds & lids with transparent PDMS Dow Sylgard™ 184 Silicone microfluidic part

Bottom:                          #1.5 borosilicate glass D-263^® M 

Not sterilized                 

All our products are "FOR RESEARCH ONLY!"

PimCell^® Voice Dish is an easy-to-use microfluidic dish specifically developed to handle the requirements of tissues connected to a vascular network in experiments and assays like patient derived xenograft (PDX) vascularization. Each microfluidic PimCell^® Voice Dish contains a microfluidic part with one open top chamber (OTC) connected to two enclosed perfusion channels without any physical barrier between. The OTC can be used as an organoid or spheroid compartment.

Schematic representation of a microfluidic PimCell^® Voice Dish

Microfluidic PimCell^® Dishes need end user sterilization. Please see our ''Tech Specs'' for sterilization procedure

Concept of 3D cell culture using microfluidic PimCell^® Voice Dish

The direct advantage of a microfluidic PimCell^® Voice Dish is a 3D cell culture without any dead volume always presented inside either inlets or outlets of (hydro)gel filled microfluidic channels. Using OTC design every desired 3D cell culture support can be directly introduced into the OTC chamber for gelation (i.e. gel or gel mixture with desired cells). The polymerized gel separates content of perfusion channels from the space above the cell culture chamber allowing seeding different cell types on the different part of a common 3D cell culture support. The direct benefit is an opportunity to create a novel or to modify existing in vitro 3D models for producing more valuable and reliable data. This protocol covers the basic usage of the microfluidic PimCell^® Voice Dish such as OTC loading with a 3D cell culture support like gel, hydrating microfluidic perfusion channels and seeding monolayer cells on the media channel. Staining etc. are beyond of the scope of this general illustration but could be easily adapted from different publications.

Protocol

Device Preparation

1.1 Transfer the Petri dish with a sterile microfluidic PimCell^® Voice Dish to a sterile biosafety cabinet

1.2 Open the dish and load 500 µL of deionized water or phosphate-buffered saline (PBS) between the wall of the microfluidic PimCell^® Voice Dish and its microfluidic part using a pipette. Leave the microfluidic dish with the lid on in the sterile cabinet at room temperature (RT) for 1 hour

Water could reduce evaporation during gel polymerization

Prepare Gel and Coating

2.1 Prepare desired for your cell culture coating solution and place the solution in the water bath at 37°C till use

2.2 Prepare the required amount of desired gel mixture. The microfluidic PimCell^® Voice Dish has one OTC with13 µL volume and needs at least 5 µL gel mixture to be able to prevent leaking from a perfusion channel into the OTP

OTC volume of a microfluidic PimCell^® Voice Dish is 13 µL

Keep the unpolymerized gel on ice and use gel immediately within 10 minutes after preparation

2.3 Place your pipette tip slightly above the bottom coverslip and gently dispense the gel mixture into the OTC of the microfluidic PimCell^® Voice Dish

NOTE: Correct positioning of the pipette tip with gel mixture above the OTC allows capillary forces to pull the gel mixture under a capillary pressure barrier (CPB) along the adjusted perfusion channel without the gel overflows into the perfusion channel. Gel loading can be confirmed under a brightfield microscope by observing the meniscus formation. Microfluidic PimCell^® Dishes with unpolymerized gel must be handled with care. Excessive agitation or impact cause unpolymerized gel to leak out into the perfusion channel and at least partly close the channel

OTC loading with a 3D cell culture support

2.4 Cover the PimCell^® Voice Dish with its lid and place in an incubator (37 °C, 5% CO2) for 10 min to polymerize gel

NOTE: Due to the low volumes used in microfluidics the timing of the polymerization is crucial. Evaporation can be observed after 15 min of incubation resulting in gel collapse or shrinkage

2.5 Take the microfluidic PimCell^® Voice Dish out of the incubator ant transfer to a sterile biosafety cabinet. Open the lid of the dish and gently dispense 25 µL of desired cell culture medium to each OTC above the polymerized gel

2.6 Gently add 45 µL of coating solution to the inlet of the perfusion channel. Place the pipette tip in the middle and slightly above of the inlet of the perfusion channel in order to allow the coating solution to enter the perfusion channel without trapping air bubbles. The perfusion channel should fill and the liquid should pin on the outlet without filling the outlet space

Loading coating solution

Coating solution pinning on the outlet without filling the outlet space

2.7 Incubate the coating according to common practice in literature

• Incubate PimCell^® Voice Dish at 37°C in a humidified incubator or at RT, depending on coating of choice
• Incubate as short as 15 min or as long as 48h, depending on the coating of choice

Optional: if the coating of choice generally requires a washing step washing can be achieved by aspirating the coating solution and adding washing reagent (e.g. 35 µL water or PBS) to inlet and outlet spaces. Repeat if necessary

Microfluidic media channel cell seeding

3.1 Prepare desired endothelial or epithelial cell suspension

3.2 Transfer the microfluidic PimCell^® Voice Dish from the incubator to a sterile biosafety cabinet

3.3 Carefully aspirate 35 µL coating solution from the inlet of each perfusion channel

NOTE: Do not aspirate coating solution from the perfusion channel to avoid closing the microfluidic system with an air bubble

3.4 Load 35 µL of cell suspension to the outlet of each perfusion channel. Place the pipette tip in the middle and slightly above of the outlet of the perfusion channel in order to allow the cell suspension to enter the media channel without trapping air bubbles. Visual inspection of the perfusion channel under a microscope is recommended

NOTE: Lay the PimCell^® Voice Dish on a flat surface while seeding cells into the microfluidic dish. Inclination of the dish affects the flow in the perfusion channel disturbing cell distribution

 3.5 Close the PimCell^® Voice Dish with its lid and place static in the humidified incubator at 37 °C and 5% CO₂ to allow cells to attach. The time cells need to attach is cell type dependent and generally varies between 0.5 – 3 hours

3.6 After cells have attached, add 50 µL of medium to the inlet of each perfusion channel

3.7 Close the lid of the PimCell^® Tube Dish and place the dish in the a humidified incubator at 37 °C and 5% CO₂

3.8 Refresh medium every 2–3 days on each OTC, inlet and outlet

NOTE: Then you need more volume of cell culture media (i.e. for differentiation of iPSCs or organoids ) you can remove water or the PBS from the space around microfluidic part of the  PimCell^® Voice Dish and add more medium to the dish (e.g. 1,5 mL)